+27 11 795 9500 | sales@allpronix.com
Leading Suppliers Of Industrial Technology Solutions
Product Catalogue
Connect With Us
Facebook
Google+
Twitter
YouTube
LinkedIn

Wadeco

MWS-10RF

allpronix-wadeco-mws-10rf

 Read More

MWS-DP-3 (Solids Flow Switch)

allpronix-wadeco-mws-dp-3

allpronix-wadeco-mws-st-sr-3 Read More

MWS-ST/SR-2

MWS-ST

 Read More

MWS-ST/SR-3-24V DCallpronix-wadeco-mws-st-sr-3

Read More

MWS-ST/SR-11UMWS-ST

 Read More

 

MWS-10RF (Radar continuous level sensor for powder and high temperature materials)

 allpronix-wadeco-mws-10rf MWS-10RF Microwave Range Finder consists of an antenna connected to a controller by circular waveguide tubing. The heat resistant antenna is installed in the high temperature zone, while the controller is located in a room temperature area allowing the sensor to make accurate measurements in high temperature areas without special cooling.Microwaves are unaffected by temperature, flames, vapour, airborne particles or dirt.

Unaffected by adverse conditions:

The antenna, which is the sensing head, can be installed in the high temperature zone without the need of additional cooling devices. The antenna and controller are easily connected by circular waveguide tubing, using special 90。 turns and straight pieces. Microwaves are unaffected by temperature, flames, vapour, airborne particles or dirt.

High accuracy and reliability:

Error less than 10mm. False measurements caused by double-reflected waves are eliminated through the use of rotary microwaves. The accuracy of the measured range is not affected by fluctuating temperatures nor does it deteriorate over extended periods. Utilizes filters which eliminate spurious signals.

The operational state is shown on your personal computer:

It displays an FFT spectrum, the received signal and various preset values. The received signal, FFT spectrum and the trend measurement are continuously displayed. This displayed data can be recorded and reviewed in real or accelerated time. Use of the recording and reviewing capabilities allows the system parameters to be optimised offline. The display indicates and outputs the internal temperature and any abnormal conditions. (i.e. a lowering of received signal power, rising temperature in the controller, software version mismatch and communication failures.

Read More

Back To Top


 MWS-DP-3 (Solids Flow Switch)

 allpronix-wadeco-mws-dp-3 MWS-DP-3 is a microwave based non-contact solids flow sensor. It utilizes the Doppler Effect to detect the movement of solid materials such as powders and granules in pneumatic pipelines. This low cost, reliable sensor is ideal for monitoring the flow of bulk solids in vacuum pipelines, ducts, air slides, gravity chutes, feeders and at transfer points in vibrating chutes, conveyer belts and bucket elevators, easily penetrates process build up on antenna, firebrick, refractory etc. The sensor can be installed on the exterior of a plastic or ceramic pipe and detect the flow of the material in the pipe

Non-contact & non-invasive :

The Doppler Effect of microwaves allows for non-contact flow detection. Thanks to the high penetrability of microwaves, non-invasive detection through non-conductive pipes (plastic, ceramic, glass etc.) is possible.

No moving parts :

The flow sensor has no moving mechanical parts. This eliminates wear on the sensor and ensures years of maintenance free operation.

Minimally affected by nonconductive build up on the sensing head:

Microwaves are able to penetrate nonconductive build up on the sensing head or the wall of the container/pipe.

Low cost & low maintenance:

This low cost microwave flow sensor is an ideal replacement for reed or flapper switches as there is no need for periodical cleaning or replacement.

Lightweight, compact, simple to install & operate

Read More

Back To Top


MWS-ST/SR-2 (4 Channel Deluxe Type Microwave Sensor)

 MWS-ST MWS-ST/SR-2 type microwave sensor is a level switch which consists of a transmitter and a receiver, installed face to face. It comes with four channels to allow for installation of multiple sets in close proximity. The transmitter transmits microwaves toward the receiver and an output relay in the receiver is released when the beam is obstructed. Harsh environments may result in the build-up of contaminants on the sensing surfaces; however, the sensor easily penetrates this build up, thanks to the high penetrability of microwaves

100m Range with heterodyne detection:

Approx. 100m range with a ø27mm antenna, thanks to the Heterodyne detection method.

High penetration:

Easily penetrates process build up on antenna, firebrick, refractory etc., thanks to the increased operating range.

Unaffected by adverse environments:

The sensor is unaffected by surface contaminants, flames, steam, vapour or airborne particles.

Simple beam alignment:

Easy initial beam alignment at installation, thanks to the wide beam angle.

Selectable detection mode:

Either broken beam (BLOCK) or unbroken beam (UNBLOCK) detection method may be selected.

On delay time rheostat:

On delay time, adjustable 0.1~10secs, prevents instantaneous detection of falling material whilst filling.

15 LED indicator bank:

A 15 LED indicator array displays the received power level and the sensitivity-set-point, allowing for visual sensitivity adjustment and maintenance.

No set-to-set interference:

Four channels are available, selectable by rotary switch, eliminating set-to-set interference.

Analog output (optional):

The received power level may be output as a 4 ~ 20mA analog signal.

Read More

Back To Top


MWS-ST/SR-3-24V DC (Single Point Microwave Level Sensor)

 allpronix-wadeco-mws-st-sr-3 The MWS-ST/SR-3-24V type microwave sensor is a level switch consisting of a transmitter (MWS-ST) and a receiver (MWS-SR) installed face-to-face. The transmitter emits a continuous, low power microwave beam towards the receiver and an output relay is released when the beam is obstructed.

High penetration:

Easily penetrates process build up on antenna, firebrick, refractory etc., thanks to the high penetrability of microwaves.

Unaffected by adverse environments:

The sensor is unaffected by surface contaminants, flames, steam, vapour or airborne particles.

Simple beam alignment:

Easily initial beam alignment at installation, thanks to the wide beam angle.

Sensitivity margin indicators:

The sensitivity margins are indicated on the receiver by LEDs allowing for easy visual adjustment and maintenance of the sensors.

Lightweight, compact & easy to install:

The sensor weighs less than 1kg and is housed in a compact aluminium die cast enclosure. Built-in amplifiers allow for no interconnection between the transmitter and receiver.

Improved anti-vibration:

All circuits are molded in the enclosure

Enclosure rating IP65 equivalent 

Read More

Back To Top


MWS-ST/SR-11U (Universal Power Type Microwave Sensor)

 MWS-ST MWS-ST/SR-11U type microwave sensor is a level switch which consists of a transmitter (MWS-ST) and a receiver (MWS-SR), installed face to face. The transmitter emits a continuous, low power microwave beam towards the receiver and an output relay is released when the beam is obstructed. The sensor has wide application across all areas of industry where highly reliable, non-contact level detection is required. The sensor is generally used for process control by monitoring presence/absence of product, flow/no flow conditions and point level detection in bins and silos. The sensor may also be used as a proximity switch for detection of vehicles such as dump trucks and rail cars.

Unaffected by adverse conditions

Microwaves are unaffected by temperature, flames, heavy vapour/smoke, airborne particles or dirt build up on the antenna head.Designed for industrial use

Read More

Back To Top