+27 11 795 9500 | sales@allpronix.com
Leading Suppliers Of Industrial Technology Solutions
Product Catalogue
Connect With Us
Facebook
Google+
Twitter
YouTube
LinkedIn

Acromag

951EN

951_2en_200x300

Read More

961EN

951_2en_200x300

Read More

961PB

961_2pb_200x200

Read More

967EN

967EN_200x300

Read More

983EN

989EN200x300

Read More

989EN

989EN200x300

Read More

XT1111

XT1210_1110_200X300

Read More

XT1210 

XT1210_1110_200X300

Read More

 951EN-4012 (Combo module, analog current inputs)

 951_2en_200x300 These modules provide an isolated Ethernet network interface for analog and discrete I/O signals. Multi-range analog inputs and outputs support a wide variety of industrial devices.High resolution,low noise, A/D and D/A converters deliver high accuracy and reliability. 3-way isolation further improves system performance. The discrete I/O provide monitoring and control of on/off, high/low, or open/close industrial devices.Tandem I/O provides output level control and status verification in one unit. The i2o function lets inputs on one module write directly to outputs on another module.

Special Features
  • Configurable from standard web browser
  • EtherNet/IP or Modbus TCP/IP communication with automatic 10/100Mbps negotiation
  • i2o technology for peer-to-peer communication without a network controller (see Page 14)
  • Multi-function, multi-channel stand-alone module is very economical
  • High-resolution 16-bit S-D A/D and D/A converters ensure precise measurements
  • 0-35V DC solid-state logic interface can monitor or control a wide variety of devices
  • Discrete I/O channels are individually configurable as inputs or outputs in any combination
  • Bi-directional discrete I/O facilitates read-back monitoring of the output state
  • Built-in 5.6K ohm pull-down SIP resistors (socketed)
  • Selectable failsafe modes (0%, off, last-state, or pre-defined) help prevent unsafe conditions
  • Compact packaging with pluggable terminals saves space and simplifies wiring
  •  Wide operational temperature range permits installation in extreme environments

Read More

Back To Top


961EN-4012 (Ethernet Modbus TCP/IP Analog Input Module; 6 DC current input channels, i2o capability)

951_2en_200x300 These modules provide an isolated Ethernet network interface for six analog input channels. Differential inputs eliminate ground loops and thus the need for isolators in many applications. Multi-range inputs accept signals from a variety of sensor and devices. High-resolution, low noise, A/D converters deliver high accuracy and reliability. Two Ethernet protocols are available. Select Ethernet ModbusTCP/IP or EtherNet/IP. i2o function only available on Ethernet Modbus TCP/IP models.

Features
  • Configurable from standard web browser
  • EtherNet/IP® or Ethernet Modbus TCP/IP communication with automatic 10/100Mbps data rate negotiation
  • 6-input stand-alone module is very economical
  • i2o function enables direct input-to-output communication without a network controller
  • Differential inputs eliminate ground loops
  • Universal inputs support a variety of sensors
  • High-resolution 16-bit sigma-delta A/D converters ensure precise, high accuracy measurements
  • Compact packaging with pluggable terminals saves space and simplifies wiring
  • Wide operational temperature range permits installation in extreme environments

Operating Temperature Range: -25°C to +70°C (-13° to +158°F)

Read More

Back To Top


961PB (6 DC current input channels)

961_2pb_200x200 These modules provide an isolated Profibus-DP network interface for six analog input channels. Differential inputs eliminate ground loops and thus the need for isolators in many applications. Multi-range inputs accept signals from a variety of sensor and devices. High-resolution, low noise, A/D converters deliver high accuracy and reliability.

Features
  • Standard Profibus-DP network communication with industry-standard ASIC (Siemens SPC3)
  • 6-input stand-alone module is very economical
  • Differential inputs eliminate ground loops
  • Universal inputs support a variety of sensors
  • High-resolution 16-bit sigma-delta A/D converters ensure precise, high accuracy measurements
  • Compact packaging with pluggable terminals saves space and simplifies wiring
  • Wide operational temperature range permits installation in extreme environments:
  • -25 to 70°C (-13 to 158°F).
  • AC current sensor used with 961PB DC current input modules. One sensor per channel is required.

Read More

Back To Top


967EN (Ethernet Modbus TCP/IP Analog Input Module: 8-channel differential analog current input module, i2o capability, industrial-grade)

967EN_200x300 These modules interface high-level analog input signals to an Ethernet network. A high-performance design ensures reliable measurements and dependable operation. Industrial-grade models add a configurable integrator/totalizer plus superior accuracy and temperature performance compared to the economical commercial-grade version

Features
  • High-resolution 16-bit A/D
  • Fast scanning of all channels in 8mS
  • 3-way isolation and surge suppression
  • Peer-to-peer i2o communication with percent-of-span or timed-based updates
  • Configurable integration/totalization function with non-volatile registers
  • Dual-format 16/32-bit data registers
  • Scaling registers on all channels
  • Configurable sample averaging
  • Automatic calibration and self-test
  • User-adjustable TCP Ports 1-99,999 for advanced network configuration
  • Web browser configuration with copy utility for fast setup

Read More

Back To Top


983EN-4012 (Modbus TCP/IP Discrete I/O Module: 12 input channels)

 989EN200x300  These modules provide an isolated Ethernet network interface for twelve discrete input and/or output channels. The outputs provide direct on/off, high/low, or open/close control of industrial devices. The inputs sense the status of motors, pumps, valves and other equipment. The 983EN model with tandem I/O provides output level control and status verification in one unit. Two Ethernet protocols are available. Select Ethernet Modbus TCP/IP or EtherNet/IP. i2o function is only available on Ethernet Modbus TCP/IP modules with discrete outputs.

Special Features
  • Configurable from standard web browser
  • EtherNet/IP® or Ethernet Modbus TCP/IP communication with automatic 10/100Mbps data rate negotiation
  • 12-channel stand-alone module has far lower start-up cost than multi-piece block I/O systems
  • 0-35V DC solid-state logic interface can monitor or control a wide variety of devices
  • i2o function enables direct input-to-output communication without a network controller
  • Bidirectional I/O models facilitate loopback monitoring of the output state
  • Socketed SIP resistors provide input and output 5.6K ohm pull-ups to the excitation supply
  • Three selectable failsafe modes (off, last-state, or pre-defined) help prevent unsafe conditions
  • Compact packaging with pluggable terminals saves space and simplifies wiring
  • Wide operational temperature range: -25°C to +70°C (-13°F to +158°F).
  • Approvals: CE/ATEX marked; UL, cUL listed, Class 1 Div 2 Groups A, B, C, D; EtherNet/IP, Modbus/TCP conformance tested.

Read More

Back To Top


 989EN (Industrial-Grade Ethernet Modbus TCP/IP Discrete I/O Module with Counter/Timers; 16 channels)

 989EN200x300 These modules provide an isolated Ethernet interface for any input/output mix of up to 16 discrete signals. Inputs sense status of dry contacts, switches, power supplies, and DC logic. Industrial-grade units have eight 32-bit pulse counters with timers, alarms, and non-volatile memory for metering, totalizing, and low-frequency periodic measurement. Outputs control solid-state switching of lamps, horns, and other devices.

Features
  • 16 solid-state discrete I/O channels (any mix of inputs/outputs)
  • High speed 1mS updates for all 16 channels
  • 3-way isolation and surge suppression
  • Web browser configuration
  • Automatic MDI/MDI-X negotiation
  • Inputs accept 2- or 3-wire sensors and active logic switches (dry contacts, prox, namur, 5-28V DC logic)
  • Inputs detect level and change of state
  • 8 configurable counter/timers
  • 32-bit up/down pulse/event counters (with non-volatile memory)
  • 16-bit periodic timers for “last pulse”
  • Momentary/latch alarms (each counter)
  • Programmable debounce (0-65 seconds with 1mS resolution)
  • Programmable power-up conditions
  • Over-temperature, over-current, and over-voltage output protection
  • Ability to “read-back” output states
  • Watchdog timer output configurable for failsafe or hold-last-value operation
  • User-adjustable TCP Ports 1-99,999 for advanced network configuration
  • Self-test and auto-copy functions
  • Operating Temperature Range: 989EN-4016:-40°C to +65°C (-40°F to +149°F); 989EN-4C16:0°C to +55°C (+32°F to +131°F).

Read More

Back To Top


XT1111 (Ethernet Modbus/TCP and i2o Discrete I/O Module; 16 channels)

 XT1210_1110_200X300 These modules interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or low-side switched output operation. Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution. These units are ideal for remote monitoring, distributed control, or SCADA applications

Features
  • 16 solid-state discrete I/O channels (any mix of inputs or outputs)
  • Built-in 10K ohm pull-up resistors for 2/3-wire sensors (contacts, proximity, TTL)
  • Configurable normal/reverse input logic
  • Outputs include built-in read-back capability
  • Easy setup with Windows software via USB
  • Watchdog timer control of failsafe outputs
  • Continuously changing “heart-beat” register validates module operation
  • High-Density 22.5mm wide package with pluggable, front-facing terminals
  • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
  • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
  • Supports bussed/rail and redundant power
  • -40°C to +70°C wide temperature operation
  • Withstands 25g shock and 4g vibration
  • CE and UL/cUL Class 1 Div 2 Zone 2 approvals

Read More

Back To Top

XT1210 (Ethernet Analog Current Input Modules)

 XT1210_1110_200X300 The XT1210 offers an isolated Ethernet network interface for up to eight differential current input channels. Isolated differential inputs deliver better measurements, superior noise rejection, and eliminate the need for current loop isolators. Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective and reliable module. These units are ideal for remote monitoring, distributed control, or SCADA applications

Key Features & Benefits
  • Easy setup with Windows software via USB
  • Low input impedance (27 ohms) reduces loading on current loops
  • User-configurable sample averaging (1-200) on a per-channel basis
  • 10ms network updates for all 8 input channels
  • i2o peer-to-peer updates based on percent-of change and/or timed updates
  • High-resolution 16-bit Σ-Δ A/D converter ensures precise, high accuracy measurements
  • High-Density 22.5mm wide package with pluggable, front-facing terminals
  • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
  • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
  • Supports bussed/rail and redundant power
  • -40°C to +70°C wide temperature operation
  • Withstands 25g shock and 4g vibration
  • CE compliant. UL/cUL Class 1 Div 2 Zone 2 approvals (pending)

Read More

Back To Top